If I was building a new home, the last thing that I would want to find out at the last minute is that it has been being built with moldy building materials. This happens a lot more often and is a lot more serious than you might think that it is. Mold is a big problem in homes these days, either due to not paying attention to the condition of your home while you are living in it, due to a natural disaster such as a hurricane, or perhaps the most avoidable reason, it was built into the home that you currently live in.
Mold gets built into brand new homes all the time and it is not only the contractor’s fault, but also the owner’s for not paying attention to the building materials being used at the time. For someone paying to have the home built, what they need to do to help prevent this is to pay attention to what is going on at the building site and to visit it often. The building should be completely covered with a tarp until the walls and roof are totally finished and there is no possibility for rain, snow, or any other kind of precipitation to get into the house.
Before building begins you should inspect all the building materials such as the lumber, sheetrock, insulation, and etcetera that are being used. Inspect them and if you see any signs of mold at all, have them tested with a home test kit and set them aside until you are sure that they are not contaminated.
Something just as important as the other things mentioned here is to make sure your contractor and his or her workers are not storing the building materials directly on the ground. This is just asking for mold to start growing on these and this is completely avoidable by just raising the materials up off the ground. They should come into contact with the soil as little as possible, if at all.
Mold testing during different stages of the home’s development should also take place. The testing should be in the beginning, near the middle, and after the home is completed.
As long as you pay attention to what is going on around the new site of your home while your contractor is working on it, you should be able to almost completely avoid mold being built into your home.
Jim Corkern is a writer and promoter of quality
Houston Fire Damage Water Restoration Contractor companies and
Los Angeles Water Damage and Restoration Services.
Saturday, September 29, 2007
Cleaning Moldy Fabric
Sometimes we look into the backs of our closets while we are cleaning them out and we discover an old article of clothing with a fuzzy substance all over it. If you find something like this in the back of your closet, the best thing to do is drop it immediately and go wash your hands. What you were handling was a piece of clothing that has been contaminated with mold and it has been advised to not touch mold spores with your bare hands. This can possibly cause an allergic reaction or just some skin rashes, but either way, there will probably be consequences to deal with.
Most items of clothing that are contaminated with mold can be cleaned and the mold done away with, but most of the time the mold ends up leaving stains. Using bleach to remove the stains can be effective if you are dealing with mold on white clothing, but this is not always the case and chlorine bleach is not effective in killing molds on porous surfaces. You can use a brush to remove the majority of the mold and put a pre-wash spray on it; allow this to soak for about 45 minutes and put it through the washing machine. After this, allow them to dry outside naturally in the sun. Using an artificial source of heat to dry the clothes can set the stain deeper into the fabric and if you are dealing with white clothing, the sun can actually help to bleach the fabric further.
If you are looking to remove the mold and mold stains from something that was made with real leather, you are probably not going to have any luck. Items made out of leather become discolored very easily and mold does a good job of this. They cannot usually be restored after coming into contact with mold.
You can clean off upholstery or curtains that have come into contact with mold using the same method described above and one of the best purchases you can make to keep your home mold free is a vacuum that has a HEPA filter in it. Use this vacuum and its brush attachment to suck up all the mold and its spores; the filter will make sure that the spores are not re-released into the air in your home after being collected.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
Dallas Residential Water Damage Restoration Contractors.
Most items of clothing that are contaminated with mold can be cleaned and the mold done away with, but most of the time the mold ends up leaving stains. Using bleach to remove the stains can be effective if you are dealing with mold on white clothing, but this is not always the case and chlorine bleach is not effective in killing molds on porous surfaces. You can use a brush to remove the majority of the mold and put a pre-wash spray on it; allow this to soak for about 45 minutes and put it through the washing machine. After this, allow them to dry outside naturally in the sun. Using an artificial source of heat to dry the clothes can set the stain deeper into the fabric and if you are dealing with white clothing, the sun can actually help to bleach the fabric further.
If you are looking to remove the mold and mold stains from something that was made with real leather, you are probably not going to have any luck. Items made out of leather become discolored very easily and mold does a good job of this. They cannot usually be restored after coming into contact with mold.
You can clean off upholstery or curtains that have come into contact with mold using the same method described above and one of the best purchases you can make to keep your home mold free is a vacuum that has a HEPA filter in it. Use this vacuum and its brush attachment to suck up all the mold and its spores; the filter will make sure that the spores are not re-released into the air in your home after being collected.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
Dallas Residential Water Damage Restoration Contractors.
What Causes Water Damage to Your Home?
Everyone knows that water damage to any property, whether it’s commercial or residential, is bad, but not everyone is aware of all of the different factors that can allow it to occur. There are obvious causes of water damage that most people know about like plumbing leaks and leaking roofs, but what about some of the other less common causes?
Basement walls insulated with fiberglass tend to be a problem because moisture becomes trapped behind them and the air leaks that can happen in between one floor of the home and the next or even the attic. Fiberglass absorbs water and so installing fiberglass insulation in basements is not a good idea. Installing plastic sheeting inside the wall isn’t the answer, either, because this also traps moisture.
Using blue board insulation is a bit better if you’re going to insulate your basement because this insulation allows moisture to move freely through the wall and allows it to dry out.
If the land around the home is sloped toward the home’s foundation, this can cause problems, too. Water doesn’t flow away from the home as it should and can seep into the basement or weaken the foundation and cause the house to sink slowly into the ground.
If you live in a colder climate, you should be careful to have your ceilings insulated properly because if it isn’t, it can cause what are called “ice dams” and water will leak into the house. Moisture that leaks up into the attic in the form of steam or humidity can attach itself to the inside of the roofing and cause it to not only rot, but mold to grow upon it, as well.
In warmer climates, water damage can occur due to flaws in the air conditioner or the air ducts.
Attic hatches that are not properly sealed when shut are a cause of water damage inside attics and on ceilings. Light fixtures in the home should be airtight when they are installed, especially if they are the recessed kind and exhaust fans that aren’t directed outside the house, but only into the attic can be a problem, too, whether they are from the bathroom, kitchen, or laundry room. Any exhaust fan should have a vent to the outside of the home so moisture doesn’t collect, condense, and cause the water damage you are trying to avoid.
Jim Corkern is a writer and promoter of
Emergency Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Basement walls insulated with fiberglass tend to be a problem because moisture becomes trapped behind them and the air leaks that can happen in between one floor of the home and the next or even the attic. Fiberglass absorbs water and so installing fiberglass insulation in basements is not a good idea. Installing plastic sheeting inside the wall isn’t the answer, either, because this also traps moisture.
Using blue board insulation is a bit better if you’re going to insulate your basement because this insulation allows moisture to move freely through the wall and allows it to dry out.
If the land around the home is sloped toward the home’s foundation, this can cause problems, too. Water doesn’t flow away from the home as it should and can seep into the basement or weaken the foundation and cause the house to sink slowly into the ground.
If you live in a colder climate, you should be careful to have your ceilings insulated properly because if it isn’t, it can cause what are called “ice dams” and water will leak into the house. Moisture that leaks up into the attic in the form of steam or humidity can attach itself to the inside of the roofing and cause it to not only rot, but mold to grow upon it, as well.
In warmer climates, water damage can occur due to flaws in the air conditioner or the air ducts.
Attic hatches that are not properly sealed when shut are a cause of water damage inside attics and on ceilings. Light fixtures in the home should be airtight when they are installed, especially if they are the recessed kind and exhaust fans that aren’t directed outside the house, but only into the attic can be a problem, too, whether they are from the bathroom, kitchen, or laundry room. Any exhaust fan should have a vent to the outside of the home so moisture doesn’t collect, condense, and cause the water damage you are trying to avoid.
Jim Corkern is a writer and promoter of
Emergency Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Subscribe to:
Posts (Atom)
